Hand Poured

Hand Poured

scalding hot water just poured on my hand?

how do i prevent it from blistering, what should i put on it.

it really hurts.

Ice immediately, go to the drug store or Walgreen's and buy some burn salve. DO NOT PUT BUTTER ON IT! That's an old wife's tail, doesn't work only makes it worse.

Here's a home remedy that is not bad for you and it works, take some Baking Powder and a paper towel. Put like 1/4 cup in the paper towel & fold it so it all stays in. Get it wet & place it on the worst area. It will only last for a bit, but it will give you a break from the pain

How to create a stunning 3d cast of your baby's hand of foot?

How Easy is Baby Casting?

Creating 3d castings of your baby’s hand or foot can be a very rewarding experience and needless to say, by doing it yourself, you can also save a lot of money.

The best place to start is with a baby casting kit.  For Keep’s Sake provides a standard casting kit on its own or with a frame (choose from a range of box frames).  The kit includes the following:

Contents

• Chromatic Alginate. This is used to create the mould of the baby’s hand or foot.  For life casting Alginate is the most popular moulding compound because it is completely safe and in fact used by dentists in the mouths of both adults and children to take dental mouldings.  It can also capture all the fine creases in the skin, resulting in a life-like finish.
• High Grade Casting Powder.  This is used to create the cast and once dry can be painted in the colour of your choice.
• Poly Bags or a Container.  This will be used to create the mould in.
• Cocktail sticks. Once the cast has set and is dry and the rubbery alginate mould peeled away from it, there are often little bits of the mould left in some of the skin creases of the case.  Cocktail sticks are useful for cleaning these little pieces out
• Stirrers
• Paint and Paintbrush.
• Deep rebate box frame. This usually includes a twin aperture mount so that a photo can be displayed as well as the casting.
• Complete set of instructions.
• Glue.

There are 8 basic steps to the casting process:

Step 1 – Prepare the baby’s hand or foot by rubbing a generous amount of baby moisturiser on it.  This will help to ease it out of the mould when it’s been created.

Step 2 – Mix the alginate with the water (according to instructions). Mix vigorously to break down any lumps, the colour will turn pink whilst being mixed.

Step 3 – When the mixture has reached the desired consistency (consult instructions) you will need to pour it into the container or bag that you are using and place the foot or hand into the mixture.

Step 4 – Setting time will vary so again consult the instructions.  Usually fast setting alginate is used, given a baby’s tendancy to wriggle, which be take under a minute to set.  Once set, carefully remove the hand or foot so as not to tear the mould.

Step 5 – The casting powder is then mixed with water, stirring slowly and carefully to avoid air bubbles.  Once the mixture has reached the desired consistency it is poured bit by bit into the mould, swirling the mixture around the mould to ensure that it reaches all the nooks and crannies.  Once full the plaster is left to set.

Step 6 – Once dry, usually a few hours later, the mould can be broken off the cast.  It is a rubbery like texture and will break away easily.

Step 7 – The cast can now be painted.  Most kits include a silver or gold paint, but any colour acryllic paint can be used on the cast for an effective finish.

Step 8 – If you have chosen a kit with a frame, the last stage of the process is framing the cast.  You may find that the flat side of the cast is a little uneven and may require a little light sanding.  This can be done easily using a fine sandpaper. Once flat the casting can be stuck to the backing board and the back of the frame closed.

So how easy is baby casting?  I think you'll agree, that provided you buy the right kit and get the right instructions it's much easier that you would have ever imagined.

3D casts of your baby’s hand or foot (or both) make excellent keepsakes and will ensure that you can never forget how small they once were.  Invaluable!

About the Author

"For Keep's Sake" sells a range of baby casting kits and frames. Visit http://www.forkeepssake.co.uk to view our kits. We also sell Baby Keepsake Frames, 3D Name Frames, Wooden Wall Letters and Name Canvases.
Find us on Facebook: http://www.facebook.com/pages/For-Keeps-Sake/339796330205
Follow our Blog: http://forkeeps-sake.blogspot.com/

Hand Poured

• Decorative Wall
• Wrought Iron Metal

Tagged with: hand poured • paint • poured scalding coffee on my hand • wooden wall